HIFI Audio Play Shield for Raspberry Pi, PCM5122 I2S DAC R2 - ElectroDragon
Par un écrivain mystérieux
Description
Users can use this expansion board with the audio player system (such as: volumio, xbmc system, etc.) to build their own network HIFI player; In latest firmware, please follow configuration and choose turn on I2S, and use hifiberry dac+ sound card. Expansion board provides two kinds of output interface for external amplifier and other equipment. With it […]
Users can use this expansion board with the audio player system (such as: volumio, xbmc system, etc.) to build their own network HIFI player; In latest firmware, please follow configuration and choose turn on I2S, and use hifiberry dac+ sound card. Expansion board provides two kinds of output interface for external amplifier and other equipment. With it you can get rid of PC power consumption, power off slow, power noise and other issues. Better not use to drive earphone directly, it can work but NOT recommended and not supported. On board 3.96mm power jack for 5V power supply. On board IR infrared receiver for remote controll, support software LIRC. Volumio use guide please see here. About PCM5122 Upgrade DAC chip, using BB (acquired by TI) More high-end PCM5122 chip, Using I2S interface, not USB, control volume and audio via I2C interface. Supports 16- to 32-bit audio data formats Distortion and dynamic are very good, Support high 384kHz sampling rate, Dynamic range 112dB, Distortion -93Db. Soft rising or falling ramp and analog squelch for 120dB squelch SNR with no pops. PCM5122 also integrates a negative charge pump, the output without DC blocking capacitors; 2.1Vrms ground center output; Very good ability to suppress out-of-band noise. By supporting loads as low as 1kΩ, the PCM510xA can drive multiple parallel products. (That is, more than one amplifier at the same time). The output ports are gold plated RCV double terminals and gold plated 3.5mm headphone holder Isolated power supply design, the raspberry pie power supply and DAC part of the independent power isolation, and mutual non-interference through the beads, get rid of the current sound Solderless, plug directly to the expansion board can be used, and the use of I2S interface directly decode digital to analog, non-USB DAC interface, Increase for the two-color led to provide status display, red light for the DAC power indicator (power is bright), green for the DAC work status lights (work decoding, light, stop or not work off), a better understanding of the work of the DAC Perfect compatible Raspberry Pi official PI HAT size, PCB board with high gold plating process, curved alignment (high-end HIFI DAC arc alignment), better signal continuity and reduce the signal reflection and refraction.
Users can use this expansion board with the audio player system (such as: volumio, xbmc system, etc.) to build their own network HIFI player; In latest firmware, please follow configuration and choose turn on I2S, and use hifiberry dac+ sound card. Expansion board provides two kinds of output interface for external amplifier and other equipment. With it you can get rid of PC power consumption, power off slow, power noise and other issues. Better not use to drive earphone directly, it can work but NOT recommended and not supported. On board 3.96mm power jack for 5V power supply. On board IR infrared receiver for remote controll, support software LIRC. Volumio use guide please see here. About PCM5122 Upgrade DAC chip, using BB (acquired by TI) More high-end PCM5122 chip, Using I2S interface, not USB, control volume and audio via I2C interface. Supports 16- to 32-bit audio data formats Distortion and dynamic are very good, Support high 384kHz sampling rate, Dynamic range 112dB, Distortion -93Db. Soft rising or falling ramp and analog squelch for 120dB squelch SNR with no pops. PCM5122 also integrates a negative charge pump, the output without DC blocking capacitors; 2.1Vrms ground center output; Very good ability to suppress out-of-band noise. By supporting loads as low as 1kΩ, the PCM510xA can drive multiple parallel products. (That is, more than one amplifier at the same time). The output ports are gold plated RCV double terminals and gold plated 3.5mm headphone holder Isolated power supply design, the raspberry pie power supply and DAC part of the independent power isolation, and mutual non-interference through the beads, get rid of the current sound Solderless, plug directly to the expansion board can be used, and the use of I2S interface directly decode digital to analog, non-USB DAC interface, Increase for the two-color led to provide status display, red light for the DAC power indicator (power is bright), green for the DAC work status lights (work decoding, light, stop or not work off), a better understanding of the work of the DAC Perfect compatible Raspberry Pi official PI HAT size, PCB board with high gold plating process, curved alignment (high-end HIFI DAC arc alignment), better signal continuity and reduce the signal reflection and refraction.
Users can use this expansion board with the audio player system (such as: volumio, xbmc system, etc.) to build their own network HIFI player;, In
HIFI Audio Play Shield for Raspberry Pi, PCM5122 I2S DAC R2
This DAC module for Raspberry is based on the use of a PCM5122 digital to analog conversion chip, allowing it to support PCM streams up to 32bit
Audiophonics - DAC Board for Raspberry Pi PCM5122 I2S 32bit 384khz DSD128
Users can use this expansion board with the audio player system (such as: volumio, xbmc system, etc.) to build their own network HIFI player;, In
HIFI Audio Play Shield for Raspberry Pi, PCM5122 I2S DAC R2
HiFi DAC & Audio PCM5122 24 bit Expansion Board with DAC All Function PCM5122 Chip X920 DAC& Board Full HD Audio Expansion Board for Raspberry Pi 3 Model B / 2B /
DAC Board for Raspberry Pi PCM5122 I2S 32bit 384khz DSD128 - Audiophonics
I2S HiFi Interface DIGI DAC PCM5122 Amplifier and HiFi Digi Digital Audio Expansion Sound Card Module for Raspberry Pi 3 Model B / 2B / B : Electronics
Microphone with Max9812 Amplifier Breakout - ElectroDragon
OverviewThe Raspberry Pi mother board has one major problem with i2s audio interface. The clocks coming from CPU can only output one frequency clock
Raspberry Pi PCM5122 HIFI Audio DAC Expansion Board Compatible with Raspberry Pi 4B/3B+/3B
Raspberry Pi Expansion Board Raspberry Pi HiFi DAC+ HD Audio PCM5122 24 bit Expansion Board for Raspberry Pi 3 Model B / 2B /B+/A+/ Raspberry Pi Zero W : Electronics
OverviewThe Raspberry Pi mother board has one major problem with i2s audio interface. The clocks coming from CPU can only output one frequency clock
Raspberry Pi PCM5122 HIFI Audio DAC Expansion Board Compatible with Raspberry Pi 4B/3B+/3B
The HiFi DAC Hat compatible with Raspberry Pi 4, Zero, Zero W, 3B, 3B+ with the 40-pin connector. Connects directly to the Raspberry Pi board, no
InnoMaker Raspberry Pi HiFi DAC HAT PCM5122 HiFi DAC Audio Card Expansion Board for Raspberry Pi 4 3 B+ Pi Zero etc. (DAC HAT)
Rpi HiFi DAC Hat – InnoMaker English, USB TO CAN Analyzer, Raspberry Pi Solutions, Industrial Camera
Good performance: PCM5122 integrates a negative charge pump, and the output does not require a DC blocking capacitor; 2.1 Vrms grounded center output;
HiFi DAC+Sound Card Pifi DAC + PCM5122 DAC I2S Interface Analogue Output Signal Digital Audio Card Compatible with Raspberry Pi B + a + 2B Raspberry
OverviewThe Raspberry Pi mother board has one major problem with i2s audio interface. The clocks coming from CPU can only output one frequency clock
Raspberry Pi PCM5122 HIFI Audio DAC Expansion Board Compatible with Raspberry Pi 4B/3B+/3B
depuis
par adulte (le prix varie selon la taille du groupe)
