ESP32 – Electroslab
Par un écrivain mystérieux
Description
1- 802.11 b/g/n 2- 802.11 n (2.4 GHz), up to 150 Mbps 3- WMM 4- TX/RX A-MPDU, RX A-MSDU 5- Immediate Block ACK 7- Defragmentation 8- Automatic Beacon monitoring (hardware TSF) 9- 4 × virtual Wi-Fi interfaces
The Esp32 DevKit v1 is one of the development board created to evaluate the ESP-WROOM-32 module. It is based on the ESP32 microcontroller that boasts Wifi, Bluetooth, Ethernet and Low Power support all in a single chip. ESP32 is already integrated antenna and RF balun, power amplifier, low-noise amplifiers, filters, and power management module. The entire solution takes up the least amount of printed circuit board area. This board is used with 2.4 GHz dual-mode Wi-Fi and Bluetooth chips by TSMC 40nm low power technology. Flash Layout The internal flash of the ESP32 module is organized in a single flash area with pages of 4096 bytes each. The flash starts at address 0x00000, but many areas are reserved for Esp32 IDF SDK. There exist two different layouts based on the presence of BLE support. Power Power to the Esp32 DevKit v1 is supplied via the on-board USB Micro B connector or directly via the “VIN” pin. The power source is selected automatically. The device can operate on an external supply of 6 to 20 volts. If using more than 12V, the voltage regulator may overheat and damage the device. The recommended range is 7 to 12 volts. Connect, Register, Virtualize and Program The Esp32 DevKit v1 comes with a serial-to-usb chip on board that allows programming and opening the UART of the ESP32 module. Specifications: Microcontroller: Tensilica 32-bit Single-/Dual-core CPU Xtensa LX6 Operating Voltage: 3.3V Input Voltage: 7-12V Digital I/O Pins (DIO): 25 Analog Input Pins (ADC): 6 Analog Outputs Pins (DAC): 2 UARTs: 3 SPIs: 2 I2Cs: 3 Flash Memory: 4 MB SRAM: 520 KB Clock Speed: 240 Mhz Wi-Fi: IEEE 802.11 b/g/n/e/i Integrated TR switch, balun, LNA, power amplifier, and matching network WEP or WPA/WPA2 authentication, or open networks
The Esp32 DevKit v1 is one of the development board created to evaluate the ESP-WROOM-32 module. It is based on the ESP32 microcontroller that boasts Wifi, Bluetooth, Ethernet and Low Power support all in a single chip. ESP32 is already integrated antenna and RF balun, power amplifier, low-noise amplifiers, filters, and power management module. The entire solution takes up the least amount of printed circuit board area. This board is used with 2.4 GHz dual-mode Wi-Fi and Bluetooth chips by TSMC 40nm low power technology. Flash Layout The internal flash of the ESP32 module is organized in a single flash area with pages of 4096 bytes each. The flash starts at address 0x00000, but many areas are reserved for Esp32 IDF SDK. There exist two different layouts based on the presence of BLE support. Power Power to the Esp32 DevKit v1 is supplied via the on-board USB Micro B connector or directly via the “VIN” pin. The power source is selected automatically. The device can operate on an external supply of 6 to 20 volts. If using more than 12V, the voltage regulator may overheat and damage the device. The recommended range is 7 to 12 volts. Connect, Register, Virtualize and Program The Esp32 DevKit v1 comes with a serial-to-usb chip on board that allows programming and opening the UART of the ESP32 module. Specifications: Microcontroller: Tensilica 32-bit Single-/Dual-core CPU Xtensa LX6 Operating Voltage: 3.3V Input Voltage: 7-12V Digital I/O Pins (DIO): 25 Analog Input Pins (ADC): 6 Analog Outputs Pins (DAC): 2 UARTs: 3 SPIs: 2 I2Cs: 3 Flash Memory: 4 MB SRAM: 520 KB Clock Speed: 240 Mhz Wi-Fi: IEEE 802.11 b/g/n/e/i Integrated TR switch, balun, LNA, power amplifier, and matching network WEP or WPA/WPA2 authentication, or open networks
![ESP32 – Electroslab](https://cdn.shopify.com/s/files/1/0187/3720/1252/products/OL080.jpg?v=1598993720)
Passive Buzzer, Electroslab
ElectroSlab (@electroslab) • Instagram photos and videos
![ESP32 – Electroslab](https://electroslab.com/cdn/shop/products/AA044.jpg?v=1598294094&width=533)
On Sale Products – Electroslab
![ESP32 – Electroslab](https://cdn.shopify.com/s/files/1/0187/3720/1252/products/D099.jpg?v=1598102613&width=533)
Weight Load Cell for HX711 Sensor – Electroslab
![ESP32 – Electroslab](https://cdn.shopify.com/s/files/1/0187/3720/1252/products/electrosweb411.jpg?v=1655391776)
LCD1602 LCD 1602 IIC/I2C Blue Backlight, Electroslab
![ESP32 – Electroslab](https://tienda.bricogeek.com/8019-thickbox_default/motor-shield-para-wemos-d1-mini-tb6612fng.jpg)
Esp8266 Powering D1 Mini Through 5V Pin Electrical, 53% OFF
![ESP32 – Electroslab](https://cdn.shopify.com/s/files/1/0187/3720/1252/products/electrosweb583_400x400.jpg?v=1649761974)
XL LATEX كفوف مغطس, Electroslab
Arduino-Raspberrypi Lebanon
![ESP32 – Electroslab](https://cdn.shopify.com/s/files/1/0187/3720/1252/products/LI08.jpg?v=1593705255&width=533)
ESP32 – Electroslab
![ESP32 – Electroslab](https://cdn.shopify.com/s/files/1/0187/3720/1252/files/T1568_400x400.png?v=1694163742)
Brand New Laptop MSI KATANA B13VEK-277US 15.6 9S7-158571-277
![ESP32 – Electroslab](https://cdn.shopify.com/s/files/1/0187/3720/1252/products/AB061.jpg?v=1611523584)
ESP-01 ESP8266 ESP 8266 Serial WIFI Module, Electroslab
Esp32 Wroom 32 Official Wholesale
depuis
par adulte (le prix varie selon la taille du groupe)